Euro Rack Module Vintage edition with black front plate, With three functions: Ring modulator, sample & hold/ track & hold, slew limiter, Width: 4 HP, Depth 40 mm, Power consumption +40 mA (+ 12V)/ -30 mA (-12V)
Euro Rack Module With three functions: Ring modulator, sample & hold/ track & hold, slew limiter, Width: 4 HP, Depth: 40 mm, Power consumption +40 mA (+ 12V)/ -30 mA (-12V)
Spring reverb module in Eurorack format By way of spiral springs electronically recreates the reverb effect, Spring system with 3 separate springs, Reverb signal can be fed back to the input, Width: 8 HP, Depth: 50 mm,...
Analog Modular System Base System in LC9 suitcase with PSU3, Format: 9 HE Content of the system: 2 x standard VCO A-110, 1x Ring Modulator A-114, 1 x audio Divider A-115, 1 x VC Waveform Processor A-116, 1 x Noise /...
Filter 12 dB Multi-mode filter, in which the circuit of the SEM module is used, Cream-coloured front panel and black knobs, Width: 8HP 40.3 mm, Depth: 55 mm (measured from the rear of the front panel), Power...
Brigade device module Vintage edition, 4096 BBD stages, For the A-100 modular system, Black front panel, Width: 14 TE / HP, Depth: 60 mm, Power requirement: +80mA (+12V) / -60mA (-12V)
Brigade Device modules Vintage Edition, For BBD circuits with 2048 stages, For the A-100 modular system, Black front panel, Width: 14 TE / HP, Depth: 60 mm, Power requirement: +80mA (+12V) / -60mA (-12V)
Brigade device module Vintage edition, 1024 stages Bucket Brigade Device, For modular system A-100, Black front panel, Width: 14 TE / HP, Depth: 60 mm, Power requirement: +80mA (+12V) / -60mA (-12V)
Passive Multi-Connector Eight interconnected jacks can be split into 2 groups (solder bridge on the assembly side), Width: 2 HP, Vintage edition with black front plate
Dual Slew Limiter Vintage edition with black front plate, Contains two separate slew limiters, A limiter with one control for attack and release (0-10 seconds), A limiter with separate controls for attack and release,...
Voltage Controlled Clock Multiplier Multiplication factor can be controlled by control voltage or a regulator, Black front panel, Width: 4 HP, Depth: 35 mm, Power requirements: +50 mA (+12 V) / -0 mA (-12 V)
Analogue and Trigger Sequencer Vintage edition with black front plate, 2 Switch rows with 8 steps each, Euro rack format, Width: 50 HP, Depth: 40 mm, Power consumption: +80 mA (+12V)/ -20 mA (-12V)
Sequencer Controller Module Vintage edition with black front plate, Expansion module for A-155 (Article Nr 154958 ), Different operating modes, LED display, 8 or 16 sequencer steps, Controls up to 2x A-155 (2x A-155...
Dual sample and hold module Vintage edition with black front plate, Designed to produce 'staircase' voltages, Consists of two separate sample / hold circuits, Eurorack format, Width: 4 HP, Depth: 30 mm, Power...
Envelope Generator Parameters can be set independently, 3-Step switch for selecting the time range, Euro rack format, Width: 8 HP, Depth: 50 mm, Power requirements: +20 mA (+12V) / -20 mA (-12V), Black front panel
Mixer Module Mixers with logarithmic potentiometers, Primarily for mixing audio signals, Vintage edition with black front panel, Width: 8 HP, Depth: 35 mm, Current consumption: +10mA (+12V) / -10mA (-12V)
Dual linear/exponential VCA The character of the control scale can be switched to linear or exponential, Can be used to process both audio and control voltages, Black front panel, Width: 8 HP, Depth: 50 mm, Power...
24 dB Low Pass 1 (VCF1)Module A-120 is a voltage-controlled 24 dB low-pass filter, which filters out the high frequency components from a sound spectrum while allowing the low frequencies to pass unhindered. The cut-off...
USB/ MIDI-CV/ Gate Interface Vintage edition with black front plate, Allows the integration of the A-100 module system into a USB or MIDI system, 4 Analogue CVs, Gate signal, Width: 6 HP, Depth: 55 mm, Power...
Bus Board Compatible with the Roland AIRA series (requires PSU3 power supply), Bus board (1x), Incl. 4 connection cables with flat connectors, approx. 30 cm in length